Technical advice: 021 450 60 70 · Delivery nationwide · Blog

ONSEC
Offers
021 450 60 70 Contact

Installation and service for automation details

Product categories
OffersSee discounts ›
Gate automation antenna: frequency, mounting and cable

Automation accessories

Gate automation antenna: frequency, mounting and cable

A gate automation antenna increases the radius from which the remote opens gates. Sitting up, on the lamp or on a separate stand, it removes the signal from behind the brick pillars and the metal gates, which attenuate the radio waves. Results: Fewer repeated remote control pressures.

In short: choose an automation antenna that is closed after the frequency of the receiver (433.92 or 868.35 MHz), the mounting location and the length of the cable.

Do you need help choosing?

Tell us what you need and we'll send you the offer on the same working day.

A small range of controls often has a simple cause: the receiver sits down, behind the wall or metal. The antenna sitting up, on the lamp, on the support or on the wall, takes the signal out in the clear zone. It counts the frequency, which must coincide with the receiver, and a coaxial cable as short as possible. If you already have a flashing light, check also the variants that are caught directly on it. First check the remote control battery, then choose a gate automation antenna from the category Radio antennas.

Did you notice the gate only opens when you get close to it? Often, the cause doesn't hold remote control. The receiver is locked in a box, down by the motor. In this case, a gated automation antenna solves the problem by simple intervention. Below we see how you choose it and where you mount it.

Why does the antenna matter at an automation

The radio signal of the remote control has reduced power. The wall, the metal of the gate and the vegetation weaken it. Therefore, the receiver without antenna only catches the signal close. Thus, a gate automation antenna mounted up, facing the street, increases the useful range. In addition, the number of failed orders decreases.

However, the antenna does not repair a remote control with downloaded battery. Check the battery first, then think of an antenna for gate automation. Especially in houses with fence full of concrete, the difference is felt immediately.

A technical detail helps the understanding. The antenna works best when "it sees the remote, without major obstacles. That's why every metre of height extra can count. At the same time, adjustable antennas, such as Nice ABF, allow adjustment to the access area.

Gate automation antenna: appropriate frequency

The antenna should be given on the frequency of the receiver. Range of radio antennas ONSEC covers both common frequencies. For example, Came TOP-A433N serves systems on 433 MHz. Instead, Came TOP-A862N works on 868.35 MHz. So, a chosen wrong gate automation antenna doesn't bring any winnings.

Beninca AW and Roger R91/AN1/LR1 are still working on 433,92 MHz. As a rule, read the frequency on the receiver or remote control. Then choose an antenna with the same value. European technical standards for radio equipment you can search for ASRO.

Where do you mount a radio antenna for the gate?

The mounting place counts as much as the model. There are three main variants.

  • On flashing light: Nice ABFKIT is mounted on the LUCY range lamps.
  • A self-support offers freedom: Nice ABF comes swivel, with mounting on the support.
  • The wall or pillar shall remain the universal version: Motorline MA4 includes fixing support and cable.

The lamp antennas also have specific variants. Life SKANX uses 1 metre coaxial cable for the SPLENDOR lamp. Roger R91/AN1/LR1 matches the lamps in the R92 series. Therefore, if you already have a lamp, look for a gate automation antenna designed for it. Compatible lamps found in category signalling lamps.

Coaxial cable of the reception antenna for automation

The antenna binds to the receiver through a coaxial cable. Life SKANT comes with a three-meter cable, on 433,92 MHz. The manufacturer shall describe a description compatible with automations of various brands, if the frequency coincides. At the same time, too long a cable loses its signal. For example, Roger indicates for the H93/RX20/I receiver a RG58 cable of up to 10 m. So, keep the cable as short as possible and mount a gate automation antenna near the power plant.

Avoid parallel tracks with power cables. On the other hand, do not crush the cable under the caps or tight collars.

External antenna for automatic gates: mounting steps

  • Stop power supply before any intervention.
  • Choose a high point, overlooking the access area.
  • Fix the antenna to the lamp, support or wall.
  • Connect the core of the cable and the rod to the antenna terminals of the receiver.
  • Test the range with the remote control from several points.

In other words, a gate automation antenna mounts quickly, but requires attention to connections. If you have no experience, ask for the help of an automation installer.

What you check before you buy

  • The frequency of the receiver, written on the label or in the manual.
  • Antenna terminals on the receiver plate.
  • Place available: lamp, pole, wall or stand separately.
  • The required length of the cable to the power station.
  • Exposure to wind and blows.

Write down these data before ordering. Thus, quickly compare patterns and avoid returns. For example, Motorline MA4 comes with support and cable, so it covers a complete wall mounting. Instead, Nice ABFKIT only makes sense if you already have a LUCY lamp. A suitable gate automation antenna always starts from these few checks.

Cases in which a radio antenna for the gate helps

Some situations often occur in practice. For example, the plant is in a metal box, and the gate has a full board. Otherwise, the house is at the end of a long alley. In both cases, the signal goes weak to the receiver. On the other hand, at a gate with the receiver already up, on the pole, the win can be small. Therefore, it first analyses the position of the recipient.

Antennas for other radio systems

Category also includes external antennas for the yo and RTS protocols. They serve mainly rolls and shadowing automations with these protocols. You use them when the engine receiver is in an area with a weak signal, for example in the cassette. In addition, Fadini BIRIO A8 complete the range for Fadini automations. Thus, choose an antenna for automation gate or shade after the system you have.

Frequently Asked Questions About Antenna for Gate Automation

Is any antenna going with my receiver?

No, no. The frequency of the antenna shall coincide with the receiver, e.g. 433,92 or 868,35 MHz.

Can I stretch the antenna's cable?

You can, but with caution. Each metre more loses the signal, so it respects the lengths indicated by the manufacturer.

Where do I mount the antenna?

Upstairs, facing the street. A radio antenna for the collars works well on flashing light or on a high support.

Does the antenna solve any race problem?

Not always. Also check the remote control battery or any interference in the area. You can only then complete with a gate automation antenna.

Choose from category Radio antennas an automatic gate antenna suitable for the frequency and the assembly site. The ONSEC team helps you identify the model compatible with your receiver. For new receivers, see and radio receivers.

Recommended products

Recent articles

All articles

Cookie settings

Choose which categories you accept. Strictly necessary cookies are always active; the others start only with your consent and you can change them at any time. Cookie policy

They make the site work: shopping cart, favourites, customer account sign-in, form security and remembering your cookie choice. They cannot be disabled.

Remembers recently viewed products so you can find them easily. The data stays only in your browser.

Shows us which pages are visited and how the site is used, so we can improve it (Google Analytics).