
Remote control for rollers and blinds: Nice modular system explained
A remote control for rollers and blinds allows you to lower the shadow from one point, without going to each window. The Nice modular system goes further: the same way enters a wall plate, a table stand or a pocket heel.
In short: choose the control module, then the right support (wall, table, pocket) and check compatibility with the engine receiver.
Do you need help choosing?
Tell us what you need and we'll send you the offer on the same working day.
A modular command system grows with your house or building. Start with a module and a wall plate, then add table support or portable touch where you need it. However, always check compatibility with the existing engine receiver. Therefore, choose a remote control for rollers and blinds only once and extend it thereafter. See Nice modules and supports in the category control and programming from ONSEC.
A remote control for rollers and blinds does not necessarily mean a single plastic object with buttons. In Nice, the command is built modularly: choose the transmitter module, then the housing or the holder in which you put it. Thus, the same mode can stand on the wall, on the desk or in the pocket. In this guide you see the pieces in the ONSEC category and the way you combine them.
Why a remote control for rollers and modular blinds
First, think where you stand when you want to get down the reels. Sometimes it's by the door, sometimes at the office or on the terrace. Therefore, a fixed remote control in one place does not always reach. The NiceWay system separates the electronic support part. In other words, move the module from one support to another without reprogramming everything. Also, a remote control for rollers and modular blinds fits well with renovations when you don't want new cables in walls.
Command module: the heart of the system
It all starts from the transmitter module. For example, Nice WM001G module send commands open, stop and close for automation. The command operates individually or in a multi-group mode. According to Nice's description, the serial modules handle up to 80 automations or 240 channels. Thus, a remote control for rollers and blinds can control a single window or a whole face.
However, the number of channels only matters if the engine receivers accept the protocol used. Check, in particular, the engine file before the control. Then write down the channels allocated to each room, to find them easily later.
Opla plates: discreetly mounted roller transmitter
For a fixed point, Nice proposes Opla wall supports. They come in square version, Opla S, and rectangular version, Opla R. The plates are very small, so the module that is introduced remains discreet on the wall. Plus, you choose color from the inside.
- Black: Nice square plate WSB or the WRB rectangular plate.
- Transparent: WST and WRT models let the wall see.
- Closed grey: WSG square plate.
- Aluminium: rectangular WRA plate or square version WSA.
Thus, a remote control for rollers and wall-mounted blinds looks like an ordinary switch. Plus, you don't need a dose or cable to the motor.
Table and pocket support
On the other hand, some users prefer mobile control. For the office or the night there is Nice WEO anti-shock table stand, in orange colour. Then, for the pocket, Nice offers the Go support. Model Mini toc Nice WCG has anti-shock rubber and dark grey color. According to the manufacturer, the Go support makes any NiceWay series transmitter portable. Therefore, the same remote control for rollers and blinds accompanies you through the house.
In addition, the Nice WWW magnetic attachment allows the WAX transmitter to be caught on the wall. So you take it with you and put it back without screws.
Control for rollers and blinds: step by step
- Number first the engines and groups you want to order.
- Then check the radio protocol of the receivers in the motors.
- Choose the module with the right number of channels.
- Then decide where the order stands: wall, table or pocket.
- Match the color of the support with the inside.
- Finally schedule the groups, for example all the rolls on a front.
Thus, a remote control for rollers and blinds becomes a small control panel, not an object lost through the drawer.
Actual use scenarios
Each building uses the order differently. Therefore, here are a few typical situations.
- In an apartment, an Opla plaque next to the balcony door descends all the rolls on departure.
- In an open office, the WEO table stand is at the reception and commands the blinds on the groups.
- On a terrace, the Go heel of the pocket adjusts the shadow without roads to the wall.
- In a house upstairs, a plate on every level controls the rooms there.
In all cases, a remote control for rollers and modular blinds retain the same logic of buttons. Moreover, you can always add a new support without changing the engines. Parts for these combinations appear in the category control and programming, grouped by type of support.
Pergoes, oblones and other automations
The category is not limited to the shade of windows. For example, control unit Nice PATIOCONTROL work with the 24 V Patio actuators for pergolas. At the same time, the engines from Oblonous automations and actuators of Pergola automations I can get into the same command logic. However, compatibility depends on the receiver, so check it for each equipment. Therefore, a remote control for rollers and blinds can become command of the entire shadow zone.
Electrical safety and good practice
The radio modules work on the battery, but the engines connect to the network. That's why connecting the engines remains the job of an authorized electrician. In addition, follow the manufacturer's instructions for programming and race limits. At the same time, it changes the transmitter's battery when the range of action decreases visibly. For general information on the standards applicable to equipment, please consult Standardisation Association of Romania. In the end, a remote control for well-scheduled rollers and blinds avoid accidental controls.
Frequently Asked Questions about Roller Control and Blinds
Can I use the same mode on the wall and in the pocket?
Yes, NiceWay system allows the module to move between supports. So, you just change the housing, not the programming.
How many motors does a roller transmitter control?
It depends on how and how. The NiceWay series manages, according to the manufacturer, up to 80 automations.
Does a remote control work for rollers and blinds with any motor?
Not necessarily. Therefore, check whether the engine receiver accepts the Nice protocol.
Do I have to break the wall for the Opla board?
No, the plate is caught directly on the wall. Instead, choose the place before glue or catch.
Choose the right pieces
See all modules and supports in category control and programming or full range of shadow automations. The ONSEC team helps you to make a remote control for the reels and the right blinds for your home or office.



















